Carbon Steel Fasteners

ASTM A307 Carbon Steel Fasteners Nut Bolts Manufacturers Suppliers & Exporters in India

ASTM A307 Fasteners Nut Bolts, Fasteners Nut Bolts Mumbai, Fasteners Nut Bolts India, Fasteners Nut Bolts Uae, Fasteners Nut Bolts Iran, Fasteners Nut Bolts Iraq, Fasteners Nut Bolts Qatar, Fasteners Nut Bolts Dubai, Fasteners Nut Bolts Singapore, Fasteners Nut Bolts Daman, Fasteners Nut Bolts Saudi Arabia

Stainless Steel Fasteners:	AISI 202, 304, 304L,316, 316L, 310, 410, 420 Etc. 4.6 , 5.6, 6.6, 8.8, 10.9 & 12.9 / 'R', 'S', 'T' Conditions.	Type:	304, 304L, 304H, 310, 310S, 316, 316L, 316Ti, 317, 317L, 321, 321H

Duplex Stainless Steel Fasteners:

Nickel Other Grade Fasteners:
Other Grades:	2507, 2205, 2304, 153MA, 253MA, 309, 904L, 2595MO.
ASTM / ASME SB 162 UNS 2200 ( NICKEL 200 ) / UNS 2201 (NICKEL 201 ) ASTM / ASME SB 127UNS 4400 (MONEL 400 ) ASTM / ASME SB 424 UNS 8825 (INCONEL 825) ASTM / ASME SB 168UNS 6600 (INCONEL 600 ) / UNS 6601 ( INCONEL 601 ) ASTM / ASME SB 443 UNS 6625 (INCONEL 625) ASTM / ASME SB 574 UNS 10276 ( HASTELLOY C 276 ) ASTM / ASME SB 462 UNS 8020 ( ALLOY 20 / 20 CB 3 )
Carbon Steel Fasteners:	ASTM A307

Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60000 PSI Tensile Strength

Hot Deep Galvanized, Bloodied Etc.

Grade	Description
Types:	Bolts, nuts, Washers, Anchor Fasteners, Stud Bolts, Eye Bolt, Stud, Threaded Rod, Cotter Pin, Socket Screw, Fine Fasteners & Spares, Foundation Fasteners, etc.
Alloy Steel Fasteners:	Bare Condition, Galvanized, Phosphetised, Cadium Plated
Nickel Alloys Fasteners:	Hastelloy, 904, Titanium, Duplex Alloy 2205, Duplex Alloy 2205 Code, Duplex Alloy 2304, Duplex Alloy 2507, Inconel 718, Inconel 751, Inconel X750, Inconel 722, Inconel MA 954, Monel 400, Monel 401, Monel 404, Monel 502, Monel K500, Monel R405, Nickel 201, Nickel 205, Nickel 211, Nickel 220, Nickel 230, Nickel 233, Nickel 270 etc.
1. Scope	1.1 This specification2 covers the chemical and mechanical requirements of two grades of carbon steel bolts and studs in sizes1/4 in. through 4 in. The fasteners are designated by “Grade” denoting tensile strength and intended use, as follows:
Grade A	Bolts, studs, and threaded rod having a minimum tensile strength of 60 ksi and intended for general applications,
Grade B	Bolts, studs, and threaded rodA having a tensile strength of 60 to 100 ksi and intended for flanged joints in piping systems with cast iron flanges, and
Grade C	Replaced by Specification F1554 Gr.36

(A) Threaded rod is not usually produced to Grade B, but can be when specified by the purchaser.

1.2 This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors or similar externally threaded fasteners.

1.3 Suitable nuts are covered in Specification A563. Unless otherwise specified, the grade and style of nut for each grade of fastener, of all surface finishes, shall be as follows:

Fastener Grade and Size	Nut Grade and Style A
???A 1/4 to 11/2 in.	A, hex
??A over 11/2 to 4 in.	A, heavy hex
?B, 1/4 to 4 in.	A, heavy hex

(A) Nuts of other grades and styles having specified proof load stresses (Specification A563, Table 3) greater than the specified grade and style of nut are also suitable.

1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 Supplementary Requirement S1 of an optional nature is provided, which describes additional restrictions to be applied when bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.

1.6 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.

2. Referenced Documents (purchase separately)
ASTM Standards

F1554 Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

F1789 Terminology for F16 Mechanical Fasteners

F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

ASME Standards

B 1.1 Unified Screw Threads Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org. B 18.2.1 Square and Hex Bolts and Screws B 18.24 Part Identifying Number (PIN) Code System Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org. B18.31.3 Threaded Rods (Inch Series)

Keywords

Bolts - Bolts, Screws And Studs - Carbon Steel - Chemical Composition - Steel - Studs - Tensile Strength

ICS Code

ICS Number Code 21.060.10 (Bolts, screws, studs)

UNSPSC Code

UNSPSC Code 31161600(Bolts); 31163300(Studs)